中国喷墨论坛-喷墨技术应用-数码影像-数码印刷-数码印花

标题: EPSON-4000/4800/7400/7600/7800/9600/9800/9400报错全集 [打印本页]

作者: mwybyb 时间: 2010-1-12 12:08
标题: EPSON-4000/4800/7400/7600/7800/9600/9800/9400报错全集
0100 废墨垫寿命少（少于1%）
00000100 废墨垫寿命到，必须更换
00000101 墨管寿命到
00010000 PF马达Encoder报错
00010001 PF马达步进错误
00010002 PF马达过载
00010003 PF马达延时错误
00010004 CR马达Encoder报错
00010005 CR马达步进错误
00010006 CR马达过载
00010007 CR马达延时错误
00010008 马达控制延时错误
00010009 离合器控制延时错误
0001000A CR初试位置传感器错误
0001000C PG初试位置传感器错误
0001000D Cover传感器报错（右侧）
0001000E Cover传感器报错（左侧）
0001000F CR马达控制错误
00010010 PF马达控制错误
00020000 NVRAM 错误
00020001 初始化RAM错误
00020002 SRAM报错
00020003 DRAM报错
10000004 CPU 报错
10000006 CPU 报错
10000009 CPU 报错
1000000A CPU 报错
1000000B CPU 报错
100000 CPU 报错　　
全新整理ＥＰＳＯＮ报错全集（珍藏版）：　
0100    废墨垫寿命少（少于1%）
00000100 废墨垫寿命到，必须更换
00000101 CR（光栅）马达到达了寿命
00010000 PF（进纸）编码器检查错误
00010001 PF 马达是在步进错误
00010002 PF马达过载
00010003 PF马达延时错误
00010004 CR 编码器检查错误
00010005 CR马达步进错误
00010007 CR马达延时错误
00010008 马达控制延时错误
00010009 离合器控制延时错误
0001000A CR初试位置传感器错误
0001000C PG初试位置传感器错误
00010014 加压失败
0001001B 打印头温度错误（检查头缆线的位置和接触）
0001001D CR传感器报错（右侧）
0001001E PF传感器报错（左侧）
00010020 CSIC reading/writing 错误（检查CSIC板的接触）
00010023 RTC 分析错误
00010026 RTC 通信错误
00010027 压力泵浦微空气泄漏错误
00010028 打印头错误
0001002A CR ASIC ECU 错误
0001002D 清洁单位到达了它寿命
00010035 清洁泵侦查错误
00010036 类型B 委员会设施错误p.196
00010037 顶头热敏电阻错误（检查头缆线位置和接触，以及打印头是否匹配）
00010038 支晶体管热敏电阻错误
0001003E 压力传感器失败
0001003F 压力马达到达了它的什么寿命
00010040 打印的位置误差
00020000 NVRAM 错误
00020002 SDRAM 错误
00020003 起动节目总和错误
0002000A 程序装载错误
0002000B 内存是不足的
0Dxxxxxx 一个误差编码为调试
RTC 定时器的0Exxxxxx A time-lag
100000E0 CPU 地址错误(装载)
10000100 个CPU 地址错误
10000180 个CPU 后备的指令编码例外错
100001A0 CPU 槽孔未定义命令例外错误
100001.C0 交流电能被关闭
100005C0 CPU DMA 地址错误
10000xxx CPU 错误
0001000F CR马达控制错误
00010010 PF马达控制错误
00020000 NVRAM 错误
00020001 初始化RAM错误
00020002 SRAM报错
00020003 DRAM报错
10000004 CPU 报错
10000006 CPU 报错
10000009 CPU 报错
1000000A CPU 报错
1000000B CPU 报错
100000 CPU 报错
00000101 The CR Motor reached its end of life. p.186
00010000 PF Encoder check error p.187
00010001 The PF Motor is out of step. p.188
00010002 Overcurrent occurred on the PF Motor. p.188
00010003 The PF Motor out of position time-out error p.189
00010004 CR Encoder check error p.189
00010005 CR Motor is out of step. p.190
00010007 The CR Motor out of position time-out error p.190
00010008 Servo interrupt watchdog time-out error p.191
00010009 System interrupt watchdog time-out error p.191
0001000A Carriage home position detection error p.191
0001000C PG home position detection error p.192
00010014 Failure of pressurizing p.192
0001001B Head driver (TG) temperature error p.193
0001001D CR servo parameter error p.193
0001001E PF servo parameter error p.194
00010020 CSIC reading/writing error p.194
00010023 RTC analyzing error p.194
00010026 RTC communication error p.195
00010027 Pressure pump micro air-leak error p.195
00010028 Head error p.195
0001002A CR ASIC ECU error p.195
0001002D The Cleaning Unit reached its end of life. p.195
00010035 Pump phase detection error p.196
00010036 Type-B board installation error p.196
00010037 Head thermistor error p.196
00010038 Transistor thermistor error p.196
0001003E Pressure Senso* **ilure p.196
0001003F The Pressure Motor reached its end of life. p.197
00010040 Printing position error p.197
00020000 NVRAM error p.197
00020002 SDRAM error p.197
00020003 Boot program sum error p.198
0002000A Program load error p.198
0002000B The internal memory is insufficient. p.198
0Dxxxxxx An error code for debugging p.198
0Exxxxxx A time-lag of the RTC timer p.199
100000E0 CPU address error (load) p.199
10000100 CPU address error (store) p.199
10000180 CPU reserved command code exception error p.199
100001A0 CPU slot undefined command exception error p.200
100001C0 The AC power is shut off. p.200
100005C0 CPU DMA address error p.200
10000xxx CPU error p.200

首先是一些7600/9600上机器错误代码的分析!!!
7600/9600 Field Repair Guide
00000101    CR motor life字车电机寿命
00010000    PF motor encoder check error马达直流电机传感器错误
00010001    PF motor out of step马达直流电机
00010002    PF motor overcurrent
00010003    PF motor in-position time-out
00010004    CR motor encoder check error
00010005    CR motor out of step
00010006    CR motor overcurrent
00010007    CR motor in-position time-out
00010008    Servo interrupt watchdog time-out
00010009    System interrupt watchdog time-out
0001000A    CR home position sensor error
0001000B    PF home position sensor error
0001000C    Head slide (PG) home podition sensor error
0001000F    CR motor PWM output faulty
00010010    PF motor PWM output faulty
0001001B    Head driver(TG) temperature error
0001001D    CR servo parameter error
0001001E    PF servo parameter error
00010020    CSIC reed/right error
00010022    Ink type error(setting on printer body side)
00010023    RTC analysis error
00010025    CSIC communication error
00010028    HEAD error
00010029    Unidentified NMI
0001002A    CR ASIC ECU error
0001002B    PF ASIC ECU error
00020000    NVRAM error
00020002    SDRAM error
00020003    BOOT program SUM error
00020009    Flash memory SUM error
0002000A    Program load error
0002000B    Internal memory shortage error
0002000C    Review error
100000E0    CPU address error (load misalignment)
10000100    CPU address error (storage misalignment)
10000180    CPU reserve command code exception error
100001A0    CPU slot illegal command exception error
100005C0    CPU DMA address error
10000xxx    CPU error

欢迎光临中国喷墨论坛-喷墨技术应用-数码影像-数码印刷-数码印花 (http://new.inknet.cn/bbs/)